POLISHING
Use the Sandwox polishing system for optimal performance every time. Unique formulas quickly remove scratches and other surface defects. Additional wet time with these products allow technicians to use less material and easy clean up helps reduce process time. Sandwox polishing pads are designed to provide you optimal performance when used with our polishing system. Eliminate swirl marks on painted surfaces, even on difficult dark colored cars.
Why use 3D SPEED over other options?
This is an easy question to answer… because it works so well.
Let’s take an in-depth look at why 3D SPEED is so good and why everyone should have this product in their detailing arsenal.
3D products use the BEST abrasive technology in the world.
The most important factor when it comes to working on car paint is the abrasive technology.
Why? Because it is the abrasive technology that is touching the paint first.
It is the abrasive technology that must do the impossible. It must abrade the surface to remove defects without at the same time leaving in their place its own defects. Any abrasive technology that can do this is an engineering marvel. The fact of the matter is most paint correction products cannot do this. When it comes to abrasive technology, products either work or they don’t. There are no gray areas. Products do not kind of work.
If the products you’re used to working with remove defects, but the results always look hazy in the sun – chances are good this is micro-marring caused by inferior abrasive technology. When this happens the only way to undo the damage is to re-do the job only this time using great abrasive technology. Same yourself time, energy, and frustration – use products from 3D, including 3D SPEED.
- All-in-One product removes swirls, scratches, water spots and oxidation while leaving a layer of protection in one step.
- Use by hand or any machine.
- Fast application and super easy wipe-off.
- Infinity working time with zero dusting.
- Change cutting or finishing ability by changing pads.
- Works on any type of paint, plastics, glass, and gelcoat surfaces.
- The most popular AIO on the market for a reason!
- New cars, used cars, boats, motorcycles, RVs, and aircraft!
Technical Specifications
| Product Name | SPEED - All-In-One Polish & Wax |
| Item No. | 3D SPEED |
| Size | 8 oz / 32 oz |
IMPORTANT: Always work on a clean, cool surface in the shade. Car should already be washed and dried and if needed, use detailing clay first to remove any above surface bonded contaminants.
By Hand
Step 1: Using a clean, soft microfiber or foam applicator, apply a quarter size drop of 3D SPEED onto the applicator and then using an overlapping circular motion, spread the 3D SPEED out over a section of paint about the size of a microfiber towel or 20” x 20”. Step 2: Next gently massage the 3D SPEED over the surface for about one minute continuing with the overlapping circular motion. Step 3: Move onto a new section of paint and repeat the above process until an entire panel has been worked with 3D SPEED. Step 4: After the wax has dried to a haze, normally around 15 to 20 minutes, remove the wax beginning with the panel where you first applied the wax and then following your path-of-travel, gently and carefully remove the wax using a clean, soft microfiber towels. Turn the towel over or fold to a clean side often. For best results, switch to a clean, dry microfiber towel often.
By Orbital Polisher
Step 1: Apply 4-5 nickel sized drops of 3D SPEED to the face of the pad. Step 2: Using a slow to medium speed, spread 3D SPEED out over a section of paint no larger than 2’x2’. Step 3: Turn polisher to high speed and begin working the 3D SPEED over the panel using an overlapping, crosshatch pattern for 2-4 minutes. Step 4: Move onto a new section of paint and repeat the above process until an entire panel has been worked with 3D SPEED. Step 5: After the wax has dried to a haze, normally around 15 to 20 minutes, remove the wax beginning with the panel where you first applied the wax and then following your path-of-travel, gently and carefully remove the wax using a clean, soft microfiber towels. Turn the towel over or fold to a clean side often. For best results, switch to a clean, dry microfiber towel often.
By Rotary Polisher
Step 1: Apply a circle of 3D SPEED around the middle of the face of the pad. Step 2: Using a slow to medium speed, spread 3D SPEED out over a section of paint no larger than 2’x2’. Step 3: Using a low to medium speed, begin working the 3D SPEED over the panel using an overlapping, crosshatch pattern for 2-4 minutes. Step 4: Move onto a new section of paint and repeat the above process until an entire panel has been worked with 3D SPEED. Step 5: After the wax has dried to a haze, normally around 15 to 20 minutes, remove the wax beginning with the panel where you first applied the wax and then following your path-of-travel, gently and carefully remove the wax using a clean, soft microfiber towels. Turn the towel over or fold to a clean side often. For best results, switch to a clean, dry microfiber towel often.
Professional Technique Tips
When using a one-step cleaner/wax also called an AIO or All-in-One, on neglected paint, you WORK the product like a compound.The idea being to work the abrasives to correct the paint the same way you would work a compound or even a polish to remove swirls, scratches, water spots and oxidation. It’s the opposite of applying a non-cleaning wax, also called a finishing wax or show car wax, (this includes non-cleaning sealants). With non-cleaning waxes and sealants – you do NOT work the product like a compound, polish or AIO, you simply want to spread the product out and massage it over the paint and cover 100% of each square inch of paint for maximum paint protection.
Subscribe
Want to be notified about our NEWS. Just sign up and we'll send you a notification by email.